MBC Original Rack Functional Trainer (add-on)

2024-12-16T15:41:57+09:00

Price: 167220

Product Description

This functional trainer can be installed on MBC's original rack, and is an add-on part for adding to an existing rack.
This product is equipped with two pulleys, a lat pulldown pulley that reduces the load by 1/1 and an adjustable pulley that reduces the load by 2/2, making it highly versatile and allowing for a wide range of training.

Conventional adjustable pulleys have problems such as the pulley not being able to be set to a sufficient height, making it difficult to use for lat pulldowns, and the load is halved, making it difficult to set a sufficient weight for some exercises. However, this product solves these problems by adding a pulley for lat pulldowns.

The adjustable pulley has a 1/2 resistance, allowing for a wide range of motion required for functional training, while the lat pulldown pulley has a 1/1 resistance, making it suitable for heavy weight workouts.

When the left and right lat pulldowns are connected with a connector bar, you can perform lat pulldowns with a maximum load of 250 kg or workout using the adjustable pulley with a load of 125 kg.

specification

*Detailed specifications may be changed without notice.

Product weight : Approx. 181kg

Size : Height 225cm

Weight stack : 1 25kg (5kg increments)

Pulley ratio : Lat pulldown pulley: 1/1
Adjustable pulley: 1/2

Adjustable pulley height : 39cm-184cm (in 5cm increments)

Frame color : Black (powder coated)

Country of Origin : China

Shipping

Free shipping: **Hokkaido and Okinawa; 9,900 yen

This product will be delivered by Seino Transportation.
Delivery will be to your doorstep. Seino Transportation delivery staff cannot carry or set up the product inside the building.
Deliveries to condominiums, buildings, and apartment buildings will generally be made at the first floor entrance.
In addition, if the delivery address is in an area where Seino Transportation cannot deliver, or is located at the back of an alley where a 4-ton truck cannot enter, the item will be handed over at the nearest Seino Transportation office.
If you purchase other products at the same time, they may be delivered separately from this product by Yamato Transport, Japan Post, Sagawa Express, etc.

[Shipping size and packaging weight]
MBC's original racks divide boxes into as small pieces as possible for transportation into condominiums and apartments.
For a 210cm rack, the largest box with the support poles stored is 205cm x 30cm x 9cm, and for a 180cm rack, the largest box with the support poles stored is 175cm x 30cm x 9cm. It is not normal for a product to not fit into an elevator or pass through a door when delivered.
The heaviest box weighs approximately 30kg.

[About specifying delivery date and time]

*For private homes
For deliveries of large free weight equipment to private residences, it is not possible to specify a delivery date and time as the delivery company, Seino Transportation (Kangaroo Delivery), is currently not accepting date and time requests for deliveries to private residences.
Therefore, the item will be shipped without a specified date and time, but the delivery date and time can be adjusted to some extent by contacting the nearest Seino Transportation office after the item has been shipped and making arrangements.
When delivering free weights to private homes, if the recipient is not at home and a second delivery is required, this places a heavy burden on the delivery staff. Therefore, if you are often not at home, we ask that you make arrangements to receive the item beforehand if possible.

・Meeting method
After the product has been shipped, please contact the nearest Seino Transportation office by phone and provide the inquiry number and the date and time that you can receive the product.
The delivery store can be confirmed using the confirmation URL that will be sent to you via email when the product is shipped.

We have also asked Seino Transportation to contact the recipient by phone before delivery, but the sooner the recipient contacts us the easier it will be to arrange the desired date and time.

After placing your order, if you specify a convenient delivery date, we will ship the product a few days before that date so that it can be delivered at the specified date and time.

*For stores and corporations
You can only specify the date of delivery; you cannot specify the desired delivery time.

*Seino Transportation Office stop
When placing an order, please enter the address and name of your nearest Seino Transportation office in the designated field on the delivery address input page.
The storage period at the branch office is 10 days from the date of arrival.

[About warranty]
MBC original rack equipment is sold with a 5-year warranty against manufacturing defects and a 30-day money back guarantee.
You may return the product for any reason within 30 days of delivery, even if it has been opened or used.
We also stock spare parts so that if any defective products are found, we can quickly replace them on a part-by-part basis.
*Please contact us in advance by email or phone when returning an item.
*When returning a product, please be sure to repackage it in the original packaging it was delivered in.
*The outer packaging will be required for returns or exchanges, so please keep it for 30 days after the product arrives. If the outer packaging has been discarded, returns will not be accepted. In addition, when returning a defective product for exchange, you will need to pack it yourself. Under no circumstances will we be able to send you repackaging outer packaging or packaging materials.
*If you return the product for your own reasons, you will be responsible for the original shipping fee, return shipping fee, refund fee, and payment fee.
*For products other than MBC original racks (even if purchased together with MBC original racks), we cannot accept returns or exchanges after opening unless there is an unavoidable reason such as a defective product.

Assembly Method

Tools required for assembly

- 1 pair of 30mm wrenches or spanners

・19mm wrench

- 1 x 5mm hex wrench

- 1 x 3mm hex wrench

・Stepladder (or large footstool) 1 unit

The product comes with an assembly manual, but please be sure to check the assembly instructions page at the link below before assembling the product.

MBC Original Rack Functional Trainer Assembly Instructions Page

Suitable rack

*This product can be installed on a rack with the following dimensions: total height 210 cm, distance between posts 62.5 cm.
・MBC Half Rack Standard 210cm Type 2
・MBC Power Rack Standard 210cm Type 1 (Post spacing 62.5cm Depth 135cm)
・MBC Power Rack Standard 210cm Type 4 (Post spacing 62.5cm Depth 178cm)
-MBC Half Rack Smith Integrated 210cm *Can only be installed without Smith attachment *After installation, the upper 62.5cm top cross member will be an extra part.
*When installing, all accessory holes at the bottom must be open.
*If you have any questions or concerns about installation, please feel free to contact us using the inquiry form.

*This product is sold individually. If you want to install it on both sides of the rack, please purchase two units.

FAQ

Does it come with handles for cable training?

Handles are not included, please purchase a suitable handle separately.

How many centimeters does the ceiling need to be to be able to install it ?

The total height of the rack on which the functional trainer is mounted is 225cm, but since assembly will be difficult if there is not a gap of about 5cm between the rack and the ceiling, the ceiling in the installation location must be at least 230cm high.

How is the Functional Trainer (add-on) delivered?

The Functional Trainer (add-on) will be packed separately into 8 boxes and delivered by Seino Transportation.
Please refer to the table below for box size and weight. (The number, size and weight of packages may change without notice.)
Delivery will be to your doorstep. Seino Transportation delivery staff cannot carry or set up the product inside the building.
For condominiums and apartment buildings, delivery will generally be made at the first floor entrance.
In addition, if the delivery address is in an area where Seino Transportation cannot deliver, or is located at the back of an alley where a 4-ton truck cannot enter, the item will be handed over at the nearest Seino Transportation office.
*Depending on the delivery destination and order contents, delivery may be made by a carrier other than Seino Transportation.

As the weight stack moves up it stops moving smoothly and becomes jammed .

Try loosening both of the small bolts on the top of the guide rod, as over tightening these bolts can cause binding at the top.

When using light weights, the shaft of the weight stack may come into contact with the weight. Is there a solution ?

Please try the following methods.
1) Please make sure the floor is completely flat. If the floor is inclined, move it to a flat surface or adjust the flooring to make the floor flat.
2) Try loosening both small bolts on the guide rod top nuts. Overtightening these bolts can cause the shaft to contact the weight.
3) Check if the shaft is properly assembled to the top weight stack. There is a locking pin inside the hole of the top weight stack. Normally, the shaft is firmly assembled and fixed in the top weight stack.
If the above does not resolve your issue, please contact us by email.

The pins go in easily at the top of the weight stack , but become harder to insert as you go down.

If the pin at the bottom of the weight stack gets caught, the floor where you are installing it may be slightly tilted.
Even a slight tilt of the floor can cause the bottom of the rod to shift by several millimeters from side to side, which can cause the pin to get caught.
(Look at the bottom of the weight stack. If the tip of the rod is not in the center of the hole but is far to the right or left, it is likely that the inclination of the floor is the cause.)
As a solution to this problem, we recommend inserting something like a thin rubber washer into the rubber ring at the bottom of the guide rod to correct the slight tilt.

I can't get the pin to go in at the 5kg weight stack. Is this how it's supposed to be ?

The top weight stack is secured to the shaft by a locking pin, so please rest assured that this is not an issue.

Tab End